Pool Leak DetectionPool Leak Detection Begins With A Bucket Test And A Dye Test

Once these simple tests have been done it’s time to move on to more advanced troubleshooting techniques.

Before proceeding you should make sure that the water is as still as possible. Using a syringe carefully inject dye around a suspected area, such as the main drain or even a pool light niche or suction return jet fitting.

Water Level Loss

When the evaporation factor is ruled out, water loss in the pool can be attributed to an underground leak in the plumbing.However, locating a break in the underground plumbing can United States of America be difficult.

A company that specializes in leak detection can use a device called the Leakalyzer to determine if there is a pool leak and exactly how much the pool is losing.This device is super sensitive pool leak repair near me and shows the changes in the pool level on a digital graph in real time.

If a 75035 4900 W. Eldorado Pkwy, Suite 148 leak is found, a technician can conduct a pressure test at the location of the leak to locate the source of the leak. If the test is performed when the filtration system is turned off, it will be possible to determine if the leak is on the suction side (skimmer or drain to pump) or a pressure side leak in the return lines and jet fittings. In either case a technician can replace the plumbing at the location of the leak to stop the flow of water from the broken line.

Dye Test

A dye test can pinpoint a leak location. It’s useful around flanges like the equipment pad, skimmers and return lines as well as suspected cracks in the pool shell or plumbing.

The nontoxic dye is squirted into the water at the suspected leak site and then watched closely for several hours. If the leak is close enough, you’ll see a stream of the dye moving towards it. If you see the dye in unwanted areas such as floor drains, sump lids or flooded basements, this indicates that the home sewer and drainage system are improperly connected.

Dye tests also verify that a property is not utilizing the sanitary sewer as a storm drain, something that has happened in many cases. Various laws and codes prohibit the use of sanitary sewers to carry storm or surface waters. This information is valuable to homeowners when considering a home purchase. To perform the dye test, have access to the building sewer clean out and its cap, which is typically located along the existing sanitary sewer line.

Pressure Test

While pool leak detection methods can help find many of the easy to reach leaks, there is no substitute for a pressure test. This is done by pressurizing all of the swimming pools underground lines, including return and suction lines and any piping running to and from the equipment pad. Specialty items such as heaters and ozonators are capped or removed to prevent damage during this phase of the testing process.

Once all of the piping is pressurized and stabilized, it is possible to confirm that there are no Texas leaking pipes by adding water to each line.If the line maintains the same amount of water then it (214)-213-4637 is safe to conclude that there is no leaking pipe.

This is a very important step to ensure that any cracks in the underground plumbing are found before any landscaping work begins. A complete pressure test also helps to provide peace of mind for a new home buyer who may not have had a building inspection done on the swimming pool and its plumbing.

Inspecting the McKinney Pump

A faulty pump that is leaking is one of the most common culprits for a pool leak. You can often tell by noticing air bubbles around the return lines or corrosion on various parts of the equipment area.

Once you have located the leak location with the bucket test or dye test the next step is to inspect the pump. This is typically done while wearing goggles so that you can see the crack or hole in the vinyl liner.

Sometimes this is not possible because the pump is too high or has been removed from the pool for service. If this is the case you will need to contact a local company that can do a non-invasive underground leak detection. This involves blowing air into underground pipes and listening for sounds of water (or air) escaping to pinpoint the leak location. This is much more expensive than just hiring a professional to locate the leak for you but it may save your house from major water damage in the future